SC-MS

SPECTRUM Serve Café enhances the taste of hot beverages while improving water quality and reducing scale build up in boilers. Its innovative variable bypass head allows 0-70% bypass, for dialled in water treatment. Equipped with de-alkalisation resin, coupled with granular activated carbon, it effectively targets water hardness and reduces chlorine, unpleasant taste and odours, PFAS and microplastics, resulting in consistent final product quality.

Water with a pH below 7 is acidic and corrosive. Raising the pH will neutralise the water, removing the metallic taste and pipe corrosion, and can also reduce any iron or manganese contamination.
The backwashing head has the advantage of remixing the media and removing any debris or iron/manganese. Backwashing the units stops the media compressing and stops it going hard which can happen with in/out systems.

This pH neutralisation unit is supplied partailly assembled for shipping. Some assembly will be required. All components and instructions will be supplied.

Water with a pH below 7 is acidic and corrosive. Raising the pH will neutralise the water, removing the metallic taste and pipe corrosion, and can also reduce any iron or manganese contamination.
The backwashing head has the advantage of remixing the media and removing any debris or iron/manganese. Backwashing the units stops the media compressing and stops it going hard which can happen with in/out systems.

This pH neutralisation unit is supplied partailly assembled for shipping. Some assembly will be required. All components and instructions will be supplied.

Birm is a relatively inexpensive material which can be used for iron and manganese removal by catalytic oxidation. It requires a pH of 7 or more for iron removal and pH 8 for manganese removal. It is advised not to use Birm in combination with chlorination and the water should be free of oil and hydrogen sulphide. If the pH of the water is too low pH correction maybe required. Birm is a light, inexpensive media but often doesn’t last quite as long as other natural media.

Iron Removal Criteria
pH: 7 - 8.5 ( High pH conditions may cause the formulation of colloidal iron which is very difficult to filter out)
Alkalinity: greater than twice the combined sulphate and chloride
Organic matter: <4-5 ppm
Dissolved oxygen: at least 15% of the iron or manganese content less than 0.5% chlorine, no H2S, oil or polyphosphates
Max. Temperature 38C

Manganese Removal Criteria
pH: 8-9
Alkalinity: greater than twice the combined sulphate and chloride
Organic matter: <4-5 ppm
Dissolved oxygen: at least 15% of the iron or manganese content less than 0.5% chlorine, no H2S, oil or polyphosphates
Max. Temperature 38C

Media life expectancy is 2 to 3 years.

This Birm unit is supplied partailly assembled for shipping. Some assembly will be required. All components and instructions will be supplied.

Filox can be used for iron, manganese and hydrogen sulphide removal by catalytic oxidation. It is a robust media allowing a faster service flow rate than other iron removal media. A pH of 7 is recommended for iron removal and 8 for manganese removal. It is a heavy media requiring a strong backwash. Adding other media is possible but can impair it’s service flow rate.

Iron Removal Criteria
pH: 7-9
Iron content: <15 ppm
Oxygen:15% of iron and manganese content

Manganese Removal Criteria
pH: 8-9
Manganese content: <3 ppm
Oxygen:15% of iron and manganese content

Hydrogen Sulphide Removal Criteria
pH: 6.8 - 9
Hydrogen Sulphide content: <7 ppm

Filox is an excellant choice when tackling Iron, Iron and managanese or all three. If dealing only with manganese or only hydrogen sulphide there are better options (see seperate section).

Filox may not be the best option if you are struggling to get your pH up to the required level or you don't wish to use a seperate pH system. Filox is quite heavy so requires a high backwashing rate - if you are unable to produce the nessecary backwashing rate again you may have to look at different options or concider using two smaller systems in parallel to achieve the correct back washing rate.

• Essential component of commercial and industrial softeners.
• Available in square or rectangular sizes up to 140 litres and from 350 litres they are round with an additional opening within the lid to assist in the salt filling process.
• Comes fully equipped with brine grid and brine well.

The Coral is an extremely popular domestic water softener which features the very reliable Clack valve. Available in timer or meter configurations a stylish, softener which fits well into any utility room or kitchen. The Coral water softener can be adjusted to the exact hardness level of the water in your local area, making it efficient and saving you money.

Dimensions:
H: 581 mm
W: 280mm
D: 490mm

Technical specifications:
Connections Inlet/Outlet 3/4" BSP male parallel
Drain 1/2" Hose Connector
Overflow 1/2" Hose connector
Operating Parameters: Max operating Pressure 8 bar (116 p.s.i )
A 5 bar pressure limiting valve should be installed to protect the machine from excessive pressure
Min Operating Pressure 1 bar (14.5 p.s.i )
Max water temperature 30 degree C
Min water temperature Protect from freezing
Transformer-13amp/ 12V
Softener Resin volume 1x 10 litres
Salt Storage capacity 20Kg tablet salt
1706Ltr per cycle Capacity per regen at 300ppm hardness
900 gm Salt used per regeneration
65% Salt efficiency
50 litres / min peak flow at 2 bar pressure drop
30 litres / min Rated service flow at 1 bar pressure drop
76 litres Water used per Regeneration
1.9 1/ min Maximum flow rate to drain
72 Minutes Maximum Regeneration Time
< 1mg per litre Softened water hardness

The Coral is an extremely popular domestic water softener which features the very reliable Clack valve. Available in timer or meter configurations a stylish, softener which fits well into any utility room or kitchen. The Coral water softener can be adjusted to the exact hardness level of the water in your local area, making it efficient and saving you money.

Crown Water Softeners produced by Harvey's Water Softeners are British made high end water softeners. Made to the highest specification and performance they offer the lowest running cost of most Non-Electric Softener. Without the need for routine servicing, it makes the total cost of ownership very attractive compared to Single Tank Electric Softeners.

This softener uses fine resin beads to speed up the regeneration cycle, its dual cylinder design cuts wastage and maintenance costs. Beads in one cylinder can self-regenerate using soft water from the other, keeping valves free of lime scale damage, while the online cylinder keeps up the continuous household supply.

Superior Salt Loading
This unit uses a purpose-designed block salt which comes in an easily handled size that's more convenient to load and store. When the block needs replacing, the unit's special sliding lid gives extra easy access.

The Silent Performer
So economical - but so effective Although this water softener is very compact, its clever side-valve design allows for maximum softening capacity. So for a system that takes up little space, works unobtrusively, needs no mains electricity supply and virtually looks after itself - it's quite a performer.

Advanced Automatic Metering
It doesn't matter how much your water consumption varies, your Softener unit won't need adjusting - even if you go on holiday. That's because the water flow is accurately measured automatically, so only the right amount of salt is used at any time.

Filox can be used for iron, manganese and hydrogen sulphide removal by catalytic oxidation. It is a robust media allowing a faster service flow rate than other iron removal media. A pH of 7 is recommended for iron removal and 8 for manganese removal. It is a heavy media requiring a strong backwash. Adding other media is possible but can impair it’s service flow rate.

Iron Removal Criteria
pH: 7-9
Iron content: <15 ppm
Oxygen:15% of iron and manganese content

Manganese Removal Criteria
pH: 8-9
Manganese content: <3 ppm
Oxygen:15% of iron and manganese content

Hydrogen Sulphide Removal Criteria
pH: 6.8 - 9
Hydrogen Sulphide content: <7 ppm

Filox is an excellant choice when tackling Iron, Iron and managanese or all three. If dealing only with manganese or only hydrogen sulphide there are better options (see seperate section).

Filox may not be the best option if you are struggling to get your pH up to the required level or you don't wish to use a seperate pH system. Filox is quite heavy so requires a high backwashing rate - if you are unable to produce the nessecary backwashing rate again you may have to look at different options or concider using two smaller systems in parallel to achieve the correct back washing rate.

Filox can be used for iron, manganese and hydrogen sulphide removal by catalytic oxidation. It is a robust media allowing a faster service flow rate than other iron removal media. A pH of 7 is recommended for iron removal and 8 for manganese removal. It is a heavy media requiring a strong backwash. Adding other media is possible but can impair it’s service flow rate.

Iron Removal Criteria
pH: 7-9
Iron content: <15 ppm
Oxygen:15% of iron and manganese content

Manganese Removal Criteria
pH: 8-9
Manganese content: <3 ppm
Oxygen:15% of iron and manganese content

Hydrogen Sulphide Removal Criteria
pH: 6.8 - 9
Hydrogen Sulphide content: <7 ppm

Filox is an excellant choice when tackling Iron, Iron and managanese or all three. If dealing only with manganese or only hydrogen sulphide there are better options (see seperate section).

Filox may not be the best option if you are struggling to get your pH up to the required level or you don't wish to use a seperate pH system. Filox is quite heavy so requires a high backwashing rate - if you are unable to produce the nessecary backwashing rate again you may have to look at different options or concider using two smaller systems in parallel to achieve the correct back washing rate.

NeutrAcalC systems are available in different sizes from a small 10" housing with a 4 Lpm Flow rate to a huge 12" Diameter x 54" High with 113 Lpm flow rate.

The Technology
NeutrAcalC is a water treatment technology using specifically designed beads to combat the effects of hard water and inhibit formation of limescale. Each bead is covered in imperfections called media templates that attract minerals (Limescale, carbonates) and combine them to form micro-crystals that slowly grow. The inactive microscopic crystal particles then break off and float freely through the system. These crystals make their way through the plumbing system without sticking to pipes, fixtures, valves or heating elements.

The NeutrAcalC technology differs from a conventional water softener which uses ion exchange to remove the limescale forming calcium and magnesium from water and replacing them with sodium ions. This ion exchange process requires a water meter, brine regeneration and a drain to flush during regeneration while NeutrAcalC requires none of these.

Unit Sizes Available (please select size required above)

Item Name

Max flow

Connections

Description

NeutrAcalC 10 SL

4 lpm

3/4" F BSP

10" Slimline System, 4 lpm, 3/4" BSP Female Ports

NeutrAcalC 10 BB

10 lpm

1" F BSP

10" Large Diameter System, 10 lpm, 1" BSP Female Ports

NeutrAcalC 817

15 lpm

3/4" M BSP

8" x 17" System, 15 lpm, 3/4" BSP Male Ports

NeutrAcalC 835

38 lpm

1" M BSP

8" x 35" System, 38 lpm, 1" BSP Male Ports

NeutrAcalC 935

45 lpm

1" M BSP

9" x 35" System, 45 lpm, 1" BSP Male Ports

NeutrAcalC 1035

60 lpm

1" M BSP

10" x 35" System, 60 lpm, 1" BSP Male Ports

NeutrAcalC 1054

75 lpm

1" M BSP

10" x 54" System, 75 lpm, 1" BSP Male Ports

NeutrAcalC 1252

113 lpm

1" M BSP

12" x 52" System, 113 lpm, 1" BSP Male Ports

Bypass system included for NC 817 to NC 1252

Advantages

• Stops limescale forming
• Green & Eco-friendly: no use of regenerants
• No Salt required
• No chloride in the water
• No rinsing “water saving”
• No regeneration, so no drain required
• No electricity, compact solution & easy installation
• No change in the chemical composition “healthy minerals retained”
• No effect on corrosion
• Maintain the efficiency of your boiler and heating system
• Protects appliances that use hot water
• Independently tested up to 99.6% efficiency using German DVGW protocol

The NeutrAcalC is not an ion exchange softener therefore will not produce soft water, however it will remove the effects of limescale produced by hard water.

Applications include:

• Hotels
• Offices
• Homes
• Restaurants
• Cafeterias
• Coffee shops
• Humidifiers
• Irrigation systems
• Ground source heat pumps

Tannins are a common class of organic compounds in upland water and give the water a yellow/brown tint. In highland (peaty) areas where water runs off peat the water can be virtually brown. Organic scavenging systems use resin to hold these organics which are periodically backwashed away with brine. Typically every 25 litres of resin will take out 2000ppm of organic colour before it needs regenerating.

This unit is supplied partailly assembled for shipping. Some assembly will be required. All components and instructions will be supplied.

Water with a pH below 7 is acidic and corrosive. Raising the pH will neutralise the water, removing the metallic taste and pipe corrosion, and can also reduce any iron or manganese contamination.
The backwashing head has the advantage of remixing the media and removing any debris or iron/manganese. Backwashing the units stops the media compressing and stops it going hard which can happen with in/out systems.

This pH neutralisation unit is supplied partailly assembled for shipping. Some assembly will be required. All components and instructions will be supplied.

Water with a pH below 7 is acidic and corrosive. Raising the pH will neutralise the water, removing the metallic taste and pipe corrosion, and can also reduce any iron or manganese contamination.
The backwashing head has the advantage of remixing the media and removing any debris or iron/manganese. Backwashing the units stops the media compressing and stops it going hard which can happen with in/out systems.

This pH neutralisation unit is supplied partailly assembled for shipping. Some assembly will be required. All components and instructions will be supplied.

WRAS approved – demonstrating quality and durability of the highest standard.
Proportional Brining – save on water and salt.
Slimline for easy siting and installation.
Meter control for optimum performance.
5 year parts and 2 year labour warranty – for complete peace of mind.
Flow rates up to 78 lpm.

Built in customer protect programme (CPP) that:
    Detects leaks in your plumbing system.
    Delays regeneration until 2am.
    Learns your water usage patterns to regenerate accordingly and make substantial savings on salt and water use.
    Automatically adjusts to BST and GMT time changes.

Simple 2 level programming with digital display – for quick set-up.
Complete with water hardness test kit and drain hose.
Free 10kg bag of Salt
Electrical supply – 220v 3 pin plug with plug-in transformer.

Turbidex is a unique natural clinoptilolite ore that has many outstanding advantages over common filter sand used for sediment reduction. Turbidex is very angular, rough surfaced and has microporous void spaces as small as 3 microns. This creates a surface area over 100 times greater than sand and can reduce suspended solids down to 5 microns or less (sand filters down to about 40 microns). Turbidex prevents the rapid build up of head loss and binding associated with sand filters and allows longer periods between back washes. Because of its high porosity and hydrophilic nature, Turbidex can operate at much higher flow rates than conventional sediment filters.

This sediment filter unit is supplied partailly assembled for shipping. Some assembly will be required. All components and instructions will be supplied.
 

Turbidex is a unique natural clinoptilolite ore that has many outstanding advantages over common filter sand used for sediment reduction. Turbidex is very angular, rough surfaced and has microporous void spaces as small as 3 microns. This creates a surface area over 100 times greater than sand and can reduce suspended solids down to 5 microns or less (sand filters down to about 40 microns). Turbidex prevents the rapid build up of head loss and binding associated with sand filters and allows longer periods between back washes. Because of its high porosity and hydrophilic nature, Turbidex can operate at much higher flow rates than conventional sediment filters.

This sediment filter unit is supplied partailly assembled for shipping. Some assembly will be required. All components and instructions will be supplied.