John Guest PI1212S Bulkhead Connector 3/8 inch Push Fit x 3/8 inch Push Fit
This Bulkhead Union 3/8" by 3/8" is part of the John Guest Range of Drinking Water System components – Part No. PI1212S. It enables a tube of 3/8 inches to be safely secured through a wall.

 EPDM O-ring for 20" Prism & Spectrum Housing
O-rings, seals and gaskets are often overlooked yet essential parts within filtration equipment. Key to ensuring a positve seal between different apparatus, reducing leakage potential in housings or providing exact postioning of a filter these accessories should be checked regularly as part of a diligent maintenance schedule.

John Guest Tubing is WRAS approved for potable liquid applications, including for drinking water, water coolers and dispensing or vending. Manufactured from linear low density Polyethylene (LLDPE) for its non-contaminating properties and durability, available by the 1 metre (minimum 2m lengths) to suit either 1/4″ or 3/8″ tube diameters.

We stock flexible tubing to suit either 1/4″ or 3/8″ diameters, for connection to your choice of push fitting. When paired with a John Guest push fitting, this tubing offers a reliable, semi-permanent alternative to hard plumbing. Orders for more than 1 metre will be cut on a continuous roll unless specified.  Minimum quantity 2 meters. Please enter no. of meters required in qty.

DO NOT INSTALL NEAR HOT WATER PIPES - WHEN EXPOSED TO HIGH TEMPERATURE THE INTEGRITY CAN BE COMPROMISED AND RESULT IN BURSTING

These top quality rubber hoses covered with stainless steel braiding are not only more robust than the plastic hoses but are also more flexible which is especially useful when installing in a confined space (e.g. under a kitchen sink). Virtually indistrcutable, these hoses will last for years.

For use with 15mm installations they have an elbow connection at both ends with 3/4" bsp nuts. All connections are nickel plated brass. Four washers are included with each pair of hoses.

Select lengths from 0.5m, 0.75m, 1.0m, 1.25m, or 1.5m

PLEASE NOTE: Length stated is the pipe length without the connectors. Please allow approx. +10cm for the connectors.

These top quality rubber hoses covered with stainless steel braiding are not only more robust than the plastic hoses but are also more flexible which is especially useful when installing in a confined space (e.g. under a kitchen sink). Virtually indistrcutable, these hoses will last for years.

For use with 15mm installations they have an elbow connection at one end and straight connector at the other, both with 3/4" bsp nuts. All connections are nickel plated brass. Four washers are included with each pair of hoses.

Select lengths from 0.5m, 0.75m, 1.0m, 1.25m, or 1.5m

PLEASE NOTE: Length stated is the pipe length without the connectors. Please allow approx. +10cm for the connectors.

With 3/4" Connections

These top quality rubber hoses covered with stainless steel braiding are not only more robust than the plastic hoses but are also more flexible which is especially useful when installing in a confined space (e.g. under a kitchen sink). Virtually indistrcutable, these hoses will last for years.

For use with 15mm or 22mm installations, these High Flow hoses have an elbow connection at both ends with 3/4" bsp nuts. All connections are nickel plated brass. Four washers are included with each pair of hoses.

Select lengths from 0.5m, to 2m.

PLEASE NOTE: Length stated is the pipe length without the connectors. Please allow approx. +10cm for the connectors.

With 3/4" Connections

These top quality rubber hoses covered with stainless steel braiding are not only more robust than the plastic hoses but are also more flexible which is especially useful when installing in a confined space (e.g. under a kitchen sink). Virtually indistrcutable, these hoses will last for years.

For use with 15mm or 22mm installations, these High Flow hoses have an elbow connection at one end and straight connector at the other, both with 3/4" bsp nuts. All connections are nickel plated brass. Four washers are included with each pair of hoses.

Select lengths from 0.5m, to 2m.

PLEASE NOTE: Length stated is the pipe length without the connectors. Please allow approx. +10cm for the connectors.

25mm stainless hoses - straight x bent - 1.5M

1" hoses for larger softners. These are 25mm bore with 1" connections and supplies with fibre washers.

John Guest Tubing is WRAS approved for potable liquid applications, including for drinking water, water coolers and dispensing or vending. Manufactured from linear low density Polyethylene (LLDPE) for its non-contaminating properties and durability, available by the 1 metre (minimum 2m lengths) to suit either 1/4″ or 3/8″ tube diameters.

We stock flexible tubing to suit either 1/4″ or 3/8″ diameters, for connection to your choice of push fitting. When paired with a John Guest push fitting, this tubing offers a reliable, semi-permanent alternative to hard plumbing. Orders for more than 1 metre will be cut on a continuous roll unless specified.  Minimum quantity 2 meters. Please enter no. of meters required in qty.

DO NOT INSTALL NEAR HOT WATER PIPES - WHEN EXPOSED TO HIGH TEMPERATURE THE INTEGRITY CAN BE COMPROMISED AND RESULT IN BURSTING

This bracket can be used for Slimline and Standard 10in and 20in Housings. It comes complete with the relevant securing screws.

Replacement valve for side filtered water lever for Cascade 3-Way Mixer tap.

Replacement valve for main hot and cold lever for Cascade 3-Way Mixer tap.

O-Rings for Pentek (Pentair) Housings: NO10 & NO20 Housings standard Diameter (BOX OF 12)

O-rings, seals and gaskets are often overlooked yet essential parts within filtration equipment. Key to ensuring a positve seal between different apparatus, reducing leakage potential in housings or providing exact postioning of a filter these accessories should be checked regularly as part of a diligent maintenance schedule.

John Guest Speedfit Straight Adaptor 1/4" Push Fit  x 3/8" NPTF Thread
This Speedfit Straight Adaptor 1/4" Push Fit  x 3/8" NPTF Thread is part of the John Guest Range of Drinking Water System components – JG Part No. PI010823S.
The adaptor is suitable to use with Everpure QL3 Heads and BW (DW) Cartridge Range Heads.

• JG Part No. PI011202S
• Push-fit technology
• Quick disconnection without the need for tools
• High chemical resistance 
• Food Quality and suitable for potable liquids and pure water applications
• Not suitable for compressed air and vacuum applications
• Quick Connector with 1/4" Thread and 3/8" Push Fit

• JG 1/4" Push Fit Elbow White
• JG Part No. CI0308W
• For use with 1/4" drinking line.

• Push-fit technology
• Quick disconnection without the need for tools
• High chemical resistance 
• Food Quality and suitable for potable liquids and pure water applications
• Not suitable for compressed air and vacuum applications
• Quick Connector with 3/8" BSPT Thread and 3/8" Push Fit
• Suitable for use with Pentek Slimline Housing with 3/8 Ports

• JG Part No. PI011223S
• Push-fit technology
• Quick disconnection without the need for tools
• High chemical resistance 
• Food Quality and suitable for potable liquids and pure water applications
• Not suitable for compressed air and vacuum applications
• Quick Connector with 3/8" Thread and 3/8" Push Fit
• Suitable for use with Everpure QL3 Heads and BW (DW) Cartridge range Heads

• John Guest 3/8" Push Fit Stem Elbow Grey
• Pack of 2

• John Guest 3/8" Stem x 3/8" Push Fit Stem Elbow
• John Guest Stem Elbow which is produced in a grey acetal copolymer making it especially suitable for applications involving potable liquids and foodstuffs for use with 3/8" drinking line
• Code PI221212S
•  

For fitting on an R.O. tank outlet.